Lotus Twincam Engine Elan Cortina Kit Car Escort
- 3200.00 £
- Published date: March 26, 2024
-
- Perranporth, Cornwall, United Kingdom
Lotus Twincam Engine Elan Cortina Kit Car Escort
⭕ This engine has been built to the highest standards and is more or less a complete unit ready to drop in and go.
Basic dimensional specifications
Block bored to +30
Crank Standard/Standard (only needed a polish)
Head thickness, 116.8 -- 117.0 measured in multiple locations
Head converted to Big value with bronze guides and has been professional ported.
Block is an L, casting no is 3020E, has the ability to have a rear dipstick (currently plugged)
The engine was chemically cleaned, head pressure tested to 50psi, fully balanced
The engine has been assembled with all quality components, ACL bearings, QED Omega forged pistons (new), freshly profiled L14 cams (Kent cams), Vernier pullies (new), steel flywheel (new), steel crank pulley, HP oil pump.
Other new components
Timing chain, complete tensioner adjuster, tensioner damper, water pump, clutch plate, clutch pressure plate, oil filler cap, dip stick tube, thermostat housing, thermostat ring (special insert to allow the removal of the thermostat and maintain correct coolant flow), front cover heater hose connector, heater valve, Q55 valve springs
Carbs are dellorto DHLA 40, they were in excellent condition, even so they were cleaned and serviced (if you prefer I have a set of 40 DCOE, in good condition) Carbs will require jetting on the rolling road.
The engine has been vernier timed to match the requirements of the L14 camshafts. The suggested output power should be approx. 140 BHP which should mean it is a good fast road engine.
Included accessories
Engine stand, New High current alternator with engine mountings (reconditioned unit), VR sensor with (mounted), stainless steel exhaust manifold, water temperature gauge adaptor, ignition leads with Taylor Spiro Pro cable (8mm) MSD plug caps (long enough to use with a EDIS coil pack, distributor ends will need to be added once the ignition system is in place to get the correct lead lengths)
EDIS system, for the sharp ones out there youll have noticed that I havent mentioned a distributor. I run my engines with 3D ECUs, believe me it makes a difference! So there is a mounted VR sensor and a very expensive trigger wheel and the leads are long enough to mount the coil pack off the engine. You will need to add an ECU (I use the DTA S40 ignition only, if you want I can give you my 3D map) and either a MAP or TPS sensor (I use TPS).
Basic dimensional specifications
Block bored to +30
Crank Standard/Standard (only needed a polish)
Head thickness, 116.8 -- 117.0 measured in multiple locations
Head converted to Big value with bronze guides and has been professional ported.
Block is an L, casting no is 3020E, has the ability to have a rear dipstick (currently plugged)
The engine was chemically cleaned, head pressure tested to 50psi, fully balanced
The engine has been assembled with all quality components, ACL bearings, QED Omega forged pistons (new), freshly profiled L14 cams (Kent cams), Vernier pullies (new), steel flywheel (new), steel crank pulley, HP oil pump.
Other new components
Timing chain, complete tensioner adjuster, tensioner damper, water pump, clutch plate, clutch pressure plate, oil filler cap, dip stick tube, thermostat housing, thermostat ring (special insert to allow the removal of the thermostat and maintain correct coolant flow), front cover heater hose connector, heater valve, Q55 valve springs
Carbs are dellorto DHLA 40, they were in excellent condition, even so they were cleaned and serviced (if you prefer I have a set of 40 DCOE, in good condition) Carbs will require jetting on the rolling road.
The engine has been vernier timed to match the requirements of the L14 camshafts. The suggested output power should be approx. 140 BHP which should mean it is a good fast road engine.
Included accessories
Engine stand, New High current alternator with engine mountings (reconditioned unit), VR sensor with (mounted), stainless steel exhaust manifold, water temperature gauge adaptor, ignition leads with Taylor Spiro Pro cable (8mm) MSD plug caps (long enough to use with a EDIS coil pack, distributor ends will need to be added once the ignition system is in place to get the correct lead lengths)
EDIS system, for the sharp ones out there youll have noticed that I havent mentioned a distributor. I run my engines with 3D ECUs, believe me it makes a difference! So there is a mounted VR sensor and a very expensive trigger wheel and the leads are long enough to mount the coil pack off the engine. You will need to add an ECU (I use the DTA S40 ignition only, if you want I can give you my 3D map) and either a MAP or TPS sensor (I use TPS).
Phone number ✆ 07947 585384
Perranporth, Cornwall
Related listings
-
-
MERCEDES CLC200 GREAT CONDITION LOW MILE...
AUTO PARTS Brackley (Northamptonshire) April 23, 2024 5650.00 £ -
BMW Genuine E90 E91 E92 E82 Performance ...
AUTO PARTS Ullesthorpe (Leicestershire) April 23, 2024 1700.00 £
-
Mitsubishi Evolution EVO 4 / 5 Speed H P...
AUTO PARTS Quorn (Leicestershire) April 22, 2024 2700.00 £ -
-
-
-
BMW DINAN E36 SUPERCHARGER M50 S50 325I ...
AUTO PARTS Wigston (Leicestershire) April 21, 2024 1200.00 £ -
Vauxhall Signum 2003 3.2 I V6 24v Elite ...
AUTO PARTS Saffron Walden (Essex) April 21, 2024 899.00 £
-
-
-
2007 Cummins Onan MDKBK 9.0 Quiet Diesel...
AUTO PARTS Clayton le Moors (Lancashire) April 20, 2024 1650.00 £
-
-
-
BMW 235 Getrag Close Ratio 5 Speed Trans...
AUTO PARTS Glenrothes (Scotland) April 20, 2024 1450.00 £
-
Dodge Ram HEMI Truck 5.7L Procharger D-1...
AUTO PARTS Brighton (East Sussex) April 20, 2024 1600.00 £ -
-
-
Used Evinrude 250 High Output Direct Inj...
AUTO PARTS Charlecote (Warwickshire) April 19, 2024 2000.00 £ -
-
JDM 97 ACURA INTEGRA B18C GSR MOTOR 1.8L...
AUTO PARTS Sutton On Sea (Lincolnshire) April 19, 2024 1700.00 £
-
-
2005 Mitsubishi Lancer Evolution Engine ...
AUTO PARTS Clacton On Sea (Essex) April 18, 2024 1300.00 £ -
-
1963-1964 Corvette Rochester Fuel Inject...
AUTO PARTS Great Saling (Essex) April 18, 2024 1900.00 £ -
-
-
Corvette 427 Tripower 1967 390 And 400 H...
AUTO PARTS Rotherwick (Hampshire) April 18, 2024 1800.00 £ -
-
98 01-04 LS1 LS6 Engine T-56 Transmissio...
AUTO PARTS Chesham (Buckinghamshire) April 18, 2024 1000.00 £
-
Nissan Leaf Electric Vehicle Charging Ca...
AUTO PARTS Stoke On Trent (Staffordshire) April 18, 2024 150.00 £ -
-
ENGINE BMW M3 2008/E90 E92 BMW/BMW M3 EN...
AUTO PARTS Pudsey (West Yorkshire) April 18, 2024 1500.00 £
-
-
-
COSWORTH 4X4 BIG TOOTH GEARBOX GEAR KIT ...
AUTO PARTS Westcliff on Sea (Essex) April 17, 2024 1600.00 £
-
-
BBS E50 CENTERLOCK MAGNESIUM MOTORSPORT ...
AUTO PARTS Near Sawrey (Cumbria) April 17, 2024 1400.00 £ -
FUll Vortech Supercharger Kit V3 03-04 S...
AUTO PARTS Stone (Staffordshire) April 17, 2024 1300.00 £
-
-
2010 Lamborghini Murcielago 6.5 LP640-Di...
AUTO PARTS Tunbridge Wells (Kent) April 17, 2024 1800.00 £ -
-
Flir M324XP Thermal Night Vision Camera
AUTO PARTS Knaresborough (North Yorkshire) April 17, 2024 1500.00 £ -
-
-
Lotus Twin Cam Race Engine.Race Car,Lotu...
AUTO PARTS Basingstoke (Hampshire) April 16, 2024 2200.00 £ -
Cessna R182 Main Landing Gear Pivot P/N ...
AUTO PARTS Towcester Silverstone (Northamptonshire) April 16, 2024 5600.00 £ -